Double Glazing Door Lock Repairs

Have you noticed that your uPVC window or door mechanism deteriorated? Perhaps the door or window handles aren't able to connect properly or are difficult to use.

You will lose energy if your double-glazed doors don't function properly. This can also increase the risk of burglary. Owen the Locksmith can repair your door lock for an affordable cost.

Snapped Key

When a key snaps off in a lock, it can be incredibly frustrating. This can also be a security risk because it could leave you vulnerable to an intruder if the door is not locked. There are a couple of quick fixes you can make to repair the issue and get your door working again.

Keep calm. If you panic and begin poking around wildly, you might just end up pushing the damaged piece of the key even further into the lock, which could make the situation worse.

Spray WD-40, or any other penetrating oil, into the lock. This will help the broken piece come out more easily. You can also use a screwdriver to break any pieces that are stuck. If you have a part of the key that is still sticking out then grab it using the help of a paperclip or any other thin metal object and pull it. Both methods work, but you must be careful not to push the damaged key further into the keyway.

Some paperclips have grooved edges which can be used as hook extractors. Jigsaw blades also work well for this. If you don't happen to have any of these items, you can bend a hook using needle-nosed pliers. Additionally, you can make use of a pair of tweezers to grab and pull out the last bit of the broken keys.

If you are unable to remove the broken piece of key then you can use a lock deicer. It is found in most hardware stores, and it works by freezing any moisture or ice that might be inside the lock.

If none of these solutions seem to work, Repair My Windows And Doors it may be time to call a locksmith. The experts at Fitlocks can quickly solve problems with uPVC door mechanisms and locks such as snapped keys and broken handles. They can also reconfigure the double glazing door mechanisms so that they are more easy to operate. Get a double glazing repair via our website or give us a call to discuss your requirements.

Broken Cylinder

A broken cylinder is an immediate security risk. It's fortunately a simple Repair My Windows And Doors for an expert locksmith to complete. A locksmith must tap the cylinder to repair it. This can be accomplished with a hammer, or any other tool. The best method is to use a wire or a long match. Then, place the end of the match or wire close to the keyway. The locksmith will then hit the lock to crack it. This is more secure than using a hammer, which can harm the lock.

The most frequent cause for cylinder head cracks is overheating. This can happen when the cylinder block and cylinder head are made of various metals, such as cast iron and aluminium. Different metals can heat up and cool down at different rates. This could cause localized hotspots to expand quicker than the rest of the cylinder.

Corrosion is another possible reason for cylinder fractures. When the cylinder head and the cylinder block aren't maintained properly, this could result in corrosion or rust, which may cause them to expand at more than they ought to. In time, this could also cause cracks.

If your uPVC window or door lock is rigid and requires more pressure to turn, it could be due to a variety of causes. A malfunctioning locking mechanism, misalignment, or an old handle are the most common reasons for this issue.

Fortunately it's a simple and affordable fix for the majority of double glazing owners. A professional locksmith will usually be able solve this problem within an hour of arriving at your property. They can replace the locking mechanisms, or change the window handles and replace the gearboxes, depending on the specific requirements of your home. A locksmith with experience will always be able advise you on the most cost-effective solutions for your home. They can even recommend upgrades to high-security 3 Star euro cylinders TS007 that give you an additional layer of security against burglars. It's a small amount to get the peace of mind that comes from knowing your uPVC door is secure.

Broken Handle

Window handle locks have complex mechanisms that wear out with time and use, so it's no surprise that they can break. It isn't always easy to pinpoint the cause of a broken window handle lock and then fix it properly.

Whether the problem is in the internal locking mechanism or the latch, repairing your broken handle will improve your uPVC double glazing door's security and allow you stop drafts. It can be expensive to repair or replace your handle if it is not done correctly and can also damage the frame and lock of your door.

Screwdriver: With the window open remove the screw that holds the handle. The screw should be on the inside of the back plate, which is usually concealed by a screw cover for aesthetic reasons. It is important to not be able to replace any internal parts of the handle such as the levers and Repair My Windows And Doors plates on either side. Ideally, keep these in the same order so you can replace them again in the event of a need.

Then, using an additional screwdriver loosen the screw that connects the handle to the spindle in the back. Once the screw is loose, pull the handle out and take the broken spindle out. Replace it with a new spindle, ensuring it's the same length (you can buy them on the internet or in hardware stores). Securely screw it in the correct position. Don't over tighten the screw as this can harm the handle as well as the window frame.

Close the handle and try it. It should function smoothly and you'll be able to open your windows once more.

While you're working on the handle, don't forget to make sure your uPVC windows are shut properly. If they're not closing properly cause draughts and damp in your home, as in addition to compromising your home's energy efficiency. A local window doctor company, like Core Sash Windows, will be able to adjust the hinges on your window frames so they shut correctly.

Broken Spindle

It is quite common that the spindle in a handle breaks rather than the handle itself. This is especially typical in uPVC tilt and turn windows. These kinds of windows require a handle that is a lock mechanism that is located in the frame of the window replacement. The handle is connected to a central rod that triggers the cams with a mushroom shape that lock into the window frame keep. If the dead latch mechanism does not open when the handle is turned it is possible that the spindle has broken This can be a very frustrating issue.

Fortunately, there are steps that can be taken to rectify this issue. A reputable locksmith can swiftly and effectively fix the issue. They can disassemble the window handle by using a tool that can remove the wheel portion of the mechanism that is where the spindle is. This can be done without damaging the handle or causing any other damage to the window frame.

After removing the wheel the technician can inspect the spindle and determine the reason for its break. This involves disassembling the spindle and examining each component part, noting any damage or excessive wear. This process is typically carried out in a clean environment by skilled technicians.

The next step is to clean the damaged spindle. This will help remove any debris or dirt that might be preventing it from working normally. After this the spindle is cleaned, it can be repaired or replaced. If it is being replaced the technician can take the dowel that is similar in size to the original and drill mating holes into both pieces of the spindle. This ensures that the new spindle is a precise fit with the handle.

If the spindle that is damaged is beyond repair, it may be necessary to replace it completely. Home centers sell generic replacements, but if the design of your window is unique then you will need to find a woodworker or cabinet maker who can replicate the exact component for you. Once the spindle has been installed, it can be fixed to the handle. Place the screw holes on the handle to the existing screws in the frame. Once the handle is in place, you can use your uPVC windows.